Hi,
Would just like to know if the following solutions can be implemented via cloud? SF, VCS, VVR, VOM and APPHA. A client has their own private cloud and wants to create their DR via cloud as well. They are looking at our solution to help them implement their DR.
Many Thanks!
Dan
We have 2 Sun 3510 arrays each containing three disks. VxVM, on Solaris 10 for SPARC, has been set up to mirror each disk, ie Array 1 Disk 1 is mirrored to Array 2 Disk 1 etc etc. We had a problem with the power to the controller of array 2 and the disks in that array ended up in a disabled and removed state.
The power has now been restored and the disks are now visible to the operating system again. However whatever we try we can not get VxVM to accept the disks.
It can see them but will not re-add them. We have followed the replace disk procedure which fails with the message 'no device available to replace'.
Any suggestions would be most gratefuly received.
Hi,
I need some help with VxVM volumes
I have been requested to restore some data from disks in a volume group
This was how it looked like before
v lvol4a - ENABLED ACTIVE 2537355264 ROUND - gen
pl lvol4a-01 lvol4a ENABLED ACTIVE 2537355264 CONCAT - RW
sd disk32-01 lvol4a-01 disk32 0 1006534400 0 xiv0_38 ENA
sd disk33-01 lvol4a-01 disk33 0 1006534400 1006534400 xiv0_39 ENA
sd disk35-01 lvol4a-01 disk35 0 524286464 2013068800 xiv0_42 ENA
pl lvol4a-02 lvol4a ENABLED ACTIVE 2537355264 CONCAT - RW
sd TMP1-01 lvol4a-02 TMP1 0 1019148544 0 xiv0_40 ENA
sd TMP2-01 lvol4a-02 TMP2 0 1308491520 1019148544 xiv0_41 ENA
sd TMP1-02 lvol4a-02 TMP1 1019148544 209715200 2327640064 xiv0_40 ENA
Then the volume was deleted as below
vxedit -g DISKGROUP001 -rf rm lvol4a
And recreated with same name and plex
vxmake -g DISKGROUP001 vol lvol4a plex=lvol4a-01
Now it looks like this..
v lvol4a - ENABLED ACTIVE 2537355264 ROUND - gen
pl lvol4a-01 lvol4a ENABLED ACTIVE 2537355264 CONCAT - RW
sd disk32-01 lvol4a-01 disk32 0 1006534400 0 xiv0_38 ENA
sd disk33-01 lvol4a-01 disk33 0 1006534400 1006534400 xiv0_39 ENA
sd disk35-01 lvol4a-01 disk35 0 524286464 2013068800 xiv0_42 ENA
Now I need to mount the data from these disks. which are siting the the VG and are not associated anywhere
disk01 auto:cdsdisk TMP1 DISKGROUP001 online
disk02 auto:cdsdisk TMP2 DISKGROUP001 online
So
1> has there been any loss data as a result of deleting and recreating volume lvol4a
2> If there is no data loss can I have the below as a spererate volume (vol_tmp) and mount the volume 2 )
pl lvol4a-02 lvol4a ENABLED ACTIVE 2537355264 CONCAT - RW
sd TMP1-01 lvol4a-02 TMP1 0 1019148544 0 xiv0_40 ENA
sd TMP2-01 lvol4a-02 TMP2 0 1308491520 1019148544 xiv0_41 ENA
sd TMP1-02 lvol4a-02 TMP1 1019148544 209715200 2327640064 xiv0_40 ENA
they dont exist in the VG only below dm exists
dm TMP1 disk01 auto 65536 1274937088 -
dm TMP2 disk02 auto 65536 1308491520 -
Hi guys,
I am a little curious about defragmentation. Probably someone can explain defragmentation.
First let me start what I have done so far:
1. Created a DG, Volume (1GB) etc (testing system only)
2. Created about 1000 1MB files
3. Deleted every 2nd file
And now I am curious. When I ran fsadm -E /local (/local is the mounted test volume of course) I get the following output:
...
Free Extents By Size
1: 2 2: 2 4: 3
8: 7 16: 6 32: 6
64: 5 128: 5 256: 6
512: 3 1024: 326 2048: 2
...
It shows clearly 326 free 1024K extents. From my understanding the file system is fragmentated now? Because when I create a large file now it would use all the 1024K extents and not one 128M extent, two 64M extent etc? Am I wrong/right?
And how can I rearrange the extents (if it is possible). I have tried various fsadm options like -e, -d and -C but without success.
BTW:
pkginfo -l VRTSvxfs
...
PSTAMP: 5.1.103.000-5.1SP1RP3_x86-2012-09-16-VERITAS-FS-142635-12
...
uname -a
SunOS sol10 5.10 Generic_142910-17 i86pc i386 i86pc
Any suggestions?
Hi,
There are 3 LUNs (450GB each) for a file system (1.3TB). Now the file system used only 25GB, is it possible to remove some LUN on line?
OS: Solaris 10
Veritas Foundation Suite: 5.0
Fstyp: Vxfs
Thanks in advance.
Hi, please send me solutions on the following topics.
The vxdclid daemon core dumps on AIX hosts with Storage Foundation 4.0 MP4
This is the output:
LABEL: CORE_DUMP
IDENTIFIER: A924A5FC
Date/Time: Tue Feb 5 06:38:24 USAST 2013
Sequence Number: 14290551
Machine Id: 00C8468E4C00
Node Id: edmerpr2
Class: S
Type: PERM
WPAR: Global
Resource Name: SYSPROC
Description
SOFTWARE PROGRAM ABNORMALLY TERMINATED
Probable Causes
SOFTWARE PROGRAM
User Causes
USER GENERATED SIGNAL
Recommended Actions
CORRECT THEN RETRY
Failure Causes
SOFTWARE PROGRAM
Recommended Actions
RERUN THE APPLICATION PROGRAM
IF PROBLEM PERSISTS THEN DO THE FOLLOWING
CONTACT APPROPRIATE SERVICE REPRESENTATIVE
Detail Data
SIGNAL NUMBER
11
USER'S PROCESS ID:
34080660
FILE SYSTEM SERIAL NUMBER
4
INODE NUMBER
501817
CORE FILE NAME
/var/opt/VRTSsfmh/core
PROGRAM NAME
vxdclid
LABEL: CORE_DUMP
IDENTIFIER: A924A5FC
Date/Time: Tue Feb 5 06:38:24 USAST 2013
Sequence Number: 14290551
Machine Id: 00C8468E4C00
Node Id: edmerpr2
Class: S
Type: PERM
WPAR: Global
Resource Name: SYSPROC
Description
SOFTWARE PROGRAM ABNORMALLY TERMINATED
Probable Causes
SOFTWARE PROGRAM
User Causes
USER GENERATED SIGNAL
Recommended Actions
CORRECT THEN RETRY
Failure Causes
SOFTWARE PROGRAM
Recommended Actions
RERUN THE APPLICATION PROGRAM
IF PROBLEM PERSISTS THEN DO THE FOLLOWING
CONTACT APPROPRIATE SERVICE REPRESENTATIVE
Detail Data
SIGNAL NUMBER
11
USER'S PROCESS ID:
34080660
FILE SYSTEM SERIAL NUMBER
4
INODE NUMBER
501817
CORE FILE NAME
/var/opt/VRTSsfmh/core
PROGRAM NAME
vxdclid
Good Day,
i need a solution on this topic below:
VxDRV:vxdmp Messages reported by vxdmp driver
B258EF25 0217225613 T S VxDRV:vxdmp Messages reported by vxdmp driver
B258EF25 0217225613 T S VxDRV:vxdmp Messages reported by vxdmp driver
All drives seem to be fine.
veritas:app2:/prod/u03/home/veritas>lsdev -Cc driver
fscsi0 Available 17-T1-01 FC SCSI I/O Controller Protocol Device
fscsi1 Available 18-T1-01 FC SCSI I/O Controller Protocol Device
fscsi2 Available 19-T1-01 FC SCSI I/O Controller Protocol Device
fscsi3 Available 20-T1-01 FC SCSI I/O Controller Protocol Device
iscsi0 Available iSCSI Protocol Device
sfw0 Available Storage Framework Module
sfwcomm0 Available 17-T1-01-FF Fibre Channel Storage Framework Comm
sfwcomm1 Available 18-T1-01-FF Fibre Channel Storage Framework Comm
sfwcomm2 Available 19-T1-01-FF Fibre Channel Storage Framework Comm
sfwcomm3 Available 20-T1-01-FF Fibre Channel Storage Framework Comm
All adapters seem fine:
veritas:app2:/prod/u03/home/veritas>lsdev -Cc adapter
ent0 Available Virtual I/O Ethernet Adapter (l-lan)
ent1 Available Virtual I/O Ethernet Adapter (l-lan)
fcs0 Available 17-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 18-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 19-T1 Virtual Fibre Channel Client Adapter
fcs3 Available 20-T1 Virtual Fibre Channel Client Adapter
vsa0 Available LPAR Virtual Serial Adapter
Environment
OS = SOlaris 10
sfha = 5.1 SP1
2013/02/19 02:20:55 VCS WARNING V-16-2-13139 Thread(2) Canceling thread (3)
2013/02/19 02:20:56 VCS ERROR V-16-2-13011 Thread(4) Resource(Mount): offline procedure did not complete within the expected time.
2013/02/19 02:20:56 VCS ERROR V-16-2-13063 Thread(4) Agent is calling clean for resource(Mount) because offline did not complete within the expected time.
2013/02/19 02:21:55 VCS WARNING V-16-2-13139 Thread(2) Canceling thread (4)
2013/02/19 02:21:57 VCS ERROR V-16-2-13006 Thread(5) Resource(Mount): clean procedure did not complete within the expected time.
2013/02/19 02:23:57 VCS WARNING V-16-2-13139 Thread(2) Canceling thread (5)
2013/02/19 02:23:57 VCS ERROR V-16-10001-5630 Mount:Mount:monitor:The file system on /dev/vx/dsk/XXX-DG/volphx is mounted on /XXXX but not accessible. You may need to manually unmount the file system.
2013/02/19 02:23:57 VCS ERROR V-16-2-13027 Thread(6) Resource(Mount) - monitor procedure did not complete within the expected time.
2013/02/19 02:23:57 VCS ERROR V-16-2-13077 Thread(6) Agent is unable to offline resource(Mount). Administrative intervention may be required.
2013/02/19 02:24:57 VCS WARNING V-16-2-13139 Thread(2) Canceling thread (6)
2013/02/19 02:25:58 VCS WARNING V-16-2-13139 Thread(2) Canceling thread (7)
2013/02/19 02:25:58 VCS ERROR V-16-10001-5630 Mount:Mount:monitor:The file system on /dev/vx/dsk/XXX-DG/volphx is mounted on /XXXX but not accessible. You may need to manually unmount the file system.
Engine LOG
Feb 19 00:03:21 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS CRITICAL V-16-1-50086 CPU usage on SEC-NODE is 100%
Feb 19 01:57:31 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13011 Thread(4) Resource(APP): offline procedure did not complete within the expected time.
Feb 19 01:57:31 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13063 Thread(4) Agent is calling clean for resource(APP) because offline did not complete within the expected time.
Feb 19 01:57:31 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13063 (SEC-NODE) Agent is calling clean for resource(APP) because offline did not complete within the expected time.
Feb 19 01:57:32 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13068 Thread(4) Resource(APP) - clean completed successfully.
Feb 19 02:02:51 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13012 Thread(5) Resource(APP): online procedure did not complete within the expected time.
Feb 19 02:02:51 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13065 Thread(5) Agent is calling clean for resource(APP) because online did not complete within the expected time.
Feb 19 02:02:51 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13065 (SEC-NODE) Agent is calling clean for resource(APP) because online did not complete within the expected time.
Feb 19 02:02:52 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13068 Thread(5) Resource(APP) - clean completed successfully.
Feb 19 02:02:52 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13071 Thread(5) Resource(APP): reached OnlineRetryLimit(0).
Feb 19 02:02:53 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS ERROR V-16-1-10303 Resource APP (Owner: Unspecified, Group: SG) is FAULTED (timed out) on sys SEC-NODE
Feb 19 02:03:20 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS CRITICAL V-16-1-50086 CPU usage on SEC-NODE is 100%
Feb 19 02:08:23 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13012 Thread(6) Resource(APP): online procedure did not complete within the expected time.
Feb 19 02:08:23 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13065 Thread(6) Agent is calling clean for resource(APP) because online did not complete within the expected time.
Feb 19 02:08:23 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13065 (SEC-NODE) Agent is calling clean for resource(APP) because online did not complete within the expected time.
Feb 19 02:08:24 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13068 Thread(6) Resource(APP) - clean completed successfully.
Feb 19 02:08:24 SEC-NODE AgentFramework[4113]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13071 Thread(6) Resource(APP): reached OnlineRetryLimit(0).
Feb 19 02:08:25 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS ERROR V-16-1-10303 Resource APP (Owner: Unspecified, Group: SG) is FAULTED (timed out) on sys SEC-NODE
Feb 19 02:20:56 SEC-NODE AgentFramework[4120]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13011 Thread(4) Resource(Mount): offline procedure did not complete within the expected time.
Feb 19 02:20:56 SEC-NODE AgentFramework[4120]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13063 Thread(4) Agent is calling clean for resource(Mount) because offline did not complete within the expected time.
Feb 19 02:20:56 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13063 (SEC-NODE) Agent is calling clean for resource(Mount) because offline did not complete within the expected time.
Feb 19 02:21:57 SEC-NODE Had[3789]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13006 (SEC-NODE) Resource(Mount): clean procedure did not complete within the expected time.
Feb 19 02:21:57 SEC-NODE AgentFramework[4120]: [ID 702911 daemon.notice] VCS ERROR V-16-2-13006 Thread(5) Resource(Mount): clean procedure did not complete within the expected time.
Feb 19 02:23:57 SEC-NODE AgentFramework[4120]: [ID 702911 daemon.notice] VCS ERROR V-16-10001-5630 Mount:Mount:monitor:The file system on /dev/vx/dsk/DISKGROUP/VOLUME is mounted on /MountPoint but not accessible. You may need to manually unmount the file system.
I have successfully passed Symantec Technical Specialist assessment of Veritas Storage Foundation 6.0 for Unix with a very good score. I had already passed both sales certifications (SSE & SSE+) of Storage Foundation 6.0
While preparing for STS assessment, I thoroughly went through all the training videos and the SF admin guide (almost 60%).
Now Symantec has conducted my interview for technical accredition of my company as Specialist partner in Storage Management. Any suggestions regarding how to prepare for interview or which particular areas the interview will focus or some topic outlines that are important from interview perspective.
Any suggestions or guidance will be highly appreciated.
Thank You
Atif Mehmood Malik
Hi ,
We are getting error mesaages under OS log file for / File System, Kindly check below error.
Feb 17 02:50:54 XX021 ufs: [ID 702911 kern.warning] WARNING: Error writing ufs log state
Feb 17 02:50:54 XX021 ufs: [ID 127457 kern.warning] WARNING: ufs log for / changed state to Error
Feb 17 02:50:54 XX021 ufs: [ID 616219 kern.warning] WARNING: Please umount(1M) / and run fsck(1M)
Feb 17 02:50:55 XX021 swapgeneric: [ID 308332 kern.info] root on /pseudo/vxio@0:0 fstype ufs
We logged a case with our vendor and they sugested the issue is because of logging option selected for / FS, and asked us to approch Symantec as we have vxvm installed on server and OS FS's are encapsulated under vxvm, We have Veritas version 4.0 installed on server and Symantec wont register a case as EOS for vxvm version 4.0 is already passed in 2011. Below is the Vxvm product installed on our system.
PKGINST: VRTSvxvm
NAME: VERITAS Volume Manager, Binaries
CATEGORY: system
ARCH: sparc
VERSION: 4.0,REV=12.06.2003.01.35
BASEDIR: /
VENDOR: VERITAS Software
DESC: Virtual Disk Subsystem
PSTAMP: VERITAS-4.0R_p1.4:14-January-2004
INSTDATE: Jun 10 2005 14:28
HOTLINE: 800-342-0652
EMAIL: support@veritas.com
STATUS: completely installed
FILES: 823 installed pathnames
20 shared pathnames
18 linked files
97 directories
411 executables
256745 blocks used (approx)
Kindly let us know what is causing the logs to get generated after every reboot and whether we can ignore such messages or it's a critical situation.
http://www.symantec.com/business/support/index?pag...
http://www.symantec.com/business/support/index?pag...
Both thes articles didn't help , also running vxdctl license init ..running vxvm 5.1 sp1 , vxdctl is in booted state .. ps -ef |grep vxconfig giving :
root 16165 1 0 Jan 29 ? 126:39 vxconfigd –kroot 16165 1 0 Jan 29 ? 126:39 vxconfigd –k
any ideas ?
Hi, all.
We have released a set of articles that contain information about troubleshooting the "failed" disk status, as reported by vxdisk.
Here is the link:
"Failed" or "failed was" is reported by vxdisk
http://www.symantec.com/docs/TECH200618
Since this is a broad topic, the "technote" is actually a set of about a dozen article that have been organized into a logical tree structure, with TECH200618 at its "root."
Let us know what you think!
Regards,
Mike
Environment
OS = Windows 2008 R2 (64bit)
SFHA = 6.0.1
One Diskgroup with one volume configured and that volume configured for replication. Replication is running fine and we tried migration between both nodes which is also running fine.
Question
- I shutdown primary Node and takeover DR node which did successful.
- I start entering data on DR site node which is also going good.
- I start Primary Node. Now both sites nodes showing Primary Primary. In this situation in Linux I do fbsyc which make DR Site Node New Primary and make the Primary Site Node New DR node. But in windows under VEA i am not able to see the fbsync command. ANy suggestion will be appriciated
-
We had the same problem. I also understand the technical procedure to disable/delete the service. I also searched for the "runonce" script/executable but didn't find anything...
My question is how do we confirm that whatever needed to "runonce" actually ran and succeeded or if nothing really needed to run? and this really is just residue
here is the log output I have:
svc:/system/VRTSperl-runonce:default (?)
State: maintenance since March 6, 2013 12:14:28 PM CST
Reason: Start method failed repeatedly, last exited with status 127.
See: http://support.oracle.com/msg/SMF-8000-KS
See: /var/svc/log/system-VRTSperl-runonce:default.log
Impact: This service is not running.
root@host:/var/adm# cat /var/svc/log/system-VRTSperl-runonce:default.log
[ Mar 6 11:21:30 Enabled. ]
[ Mar 6 11:21:30 Rereading configuration. ]
[ Mar 6 11:21:30 Executing start method ("/opt/VRTSperl/bin/runonce"). ]
/usr/sbin/sh[1]: exec: /opt/VRTSperl/bin/runonce: not found
[ Mar 6 11:21:30 Method "start" exited with status 127. ]
[ Mar 6 11:21:30 Executing start method ("/opt/VRTSperl/bin/runonce"). ]
/usr/sbin/sh[1]: exec: /opt/VRTSperl/bin/runonce: not found
[ Mar 6 11:21:30 Method "start" exited with status 127. ]
[ Mar 6 11:21:30 Executing start method ("/opt/VRTSperl/bin/runonce"). ]
/usr/sbin/sh[1]: exec: /opt/VRTSperl/bin/runonce: not found
[ Mar 6 11:21:30 Method "start" exited with status 127. ]
[ Mar 6 12:14:28 Executing start method ("/opt/VRTSperl/bin/runonce"). ]
/usr/sbin/sh[1]: exec: /opt/VRTSperl/bin/runonce: not found
[ Mar 6 12:14:28 Method "start" exited with status 127. ]
[ Mar 6 12:14:28 Executing start method ("/opt/VRTSperl/bin/runonce"). ]
/usr/sbin/sh[1]: exec: /opt/VRTSperl/bin/runonce: not found
[ Mar 6 12:14:28 Method "start" exited with status 127. ]
[ Mar 6 12:14:28 Executing start method ("/opt/VRTSperl/bin/runonce"). ]
/usr/sbin/sh[1]: exec: /opt/VRTSperl/bin/runonce: not found
[ Mar 6 12:14:28 Method "start" exited with status 127. ]
Thanks-
-John
Hello,
¿is it possible to change a disk tag without stopping the vxvm? Lets say we have a 2 node cluster in 2 sites: Y and T. The dg has 8 disks and the tag of 2 of them are wrong:
- disk 00 is tagged as T when should be Y
- disk 01 is tagged as Y when should be T
Both disks are 50 GB big and the DG has 130GB of free space.
Questions:
Can we just remove the disk and reattach them? how (there are volumes on them)?
Any easy way of exchanging the tags?
Regards,
joaquín
I found some information on this site, just want to cover my bases before doing it on our production system:
prtconf -vp|grep bootpath
root@discus2 # prtconf -vp|grep bootpath
bootpath: '/ssm@0,0/pci@18,700000/pci@1/SUNW,isptwo@4/sd@0,0:a'
root@discus2 # eeprom
nvramrc=devalias vx-disk01 /ssm@0,0/pci@18,700000/pci@1/SUNW,isptwo@4/sd@1,0:a #vx-disk01 is alternate boot disk
devalias vx-rootdisk /ssm@0,0/pci@18,700000/pci@1/SUNW,isptwo@4/sd@0,0:a #vx-rootdisk is primary boot disk
root@discus2 # vxprint -htg rootdg
DG NAME NCONFIG NLOG MINORS GROUP-ID
DM NAME DEVICE TYPE PRIVLEN PUBLEN STATE
RV NAME RLINK_CNT KSTATE STATE PRIMARY DATAVOLS SRL
RL NAME RVG KSTATE STATE REM_HOST REM_DG REM_RLNK
V NAME RVG KSTATE STATE LENGTH READPOL PREFPLEX UTYPE
PL NAME VOLUME KSTATE STATE LENGTH LAYOUT NCOL/WID MODE
SD NAME PLEX DISK DISKOFFS LENGTH [COL/]OFF DEVICE MODE
SV NAME PLEX VOLNAME NVOLLAYR LENGTH [COL/]OFF AM/NM MODE
DC NAME PARENTVOL LOGVOL
SP NAME SNAPVOL DCO
dg rootdg default default 0 1039288246.1025.discus2
dm disk01 c0t1d0s2 sliced 2888 71124291 NOHOTUSE
dm rootdisk c0t0d0s2 sliced 2888 71124291 -
v rootvol - ENABLED ACTIVE 37568556 ROUND - root
pl rootvol-01 rootvol ENABLED ACTIVE 37568556 CONCAT - RW
sd rootdisk-02 rootvol-01 rootdisk 0 37568556 0 c0t0d0 ENA
pl rootvol-02 rootvol ENABLED ACTIVE 37568556 CONCAT - RW
sd disk01-01 rootvol-02 disk01 0 37568556 0 c0t1d0 ENA
v swapvol - ENABLED ACTIVE 16776423 ROUND - swap
pl swapvol-01 swapvol ENABLED ACTIVE 16776423 CONCAT - RW
sd rootdisk-01 swapvol-01 rootdisk 37568556 16776423 0 c0t0d0 ENA
pl swapvol-02 swapvol ENABLED ACTIVE 16776423 CONCAT - RW
sd disk01-02 swapvol-02 disk01 37568556 16776423 0 c0t1d0 ENA
v var - ENABLED ACTIVE 16779312 ROUND - fsgen
pl var-01 var ENABLED ACTIVE 16779312 CONCAT - RW
sd rootdisk-03 var-01 rootdisk 54344979 16779312 0 c0t0d0 ENA
pl var-02 var ENABLED ACTIVE 16779312 CONCAT - RW
sd disk01-03 var-02 disk01 54344979 16779312 0 c0t1d0 ENA
root@discus2 #
vxplex -g rootdg dis rootvol-02
vxplex -g rootdg dis swapvol-02
vxplex -g rootdg dis var-02
vxedit -rf rm rootvol-02
vxedit -rf rm swapvol-02
vxedit -rf rm var-02
vxprint -htg rootdg (make sure the plexes were removed.)
vxdg rmdisk disk01
vxdiskunsetup -C c0t1d0
mount /dev/dsk/c0t1d0s0 /mnt
touch /mnt/etc/vx/reconfig.d/state.d/install-db
rm /mnt/etc/vx/reconfig.d/state.d/root-done
vi /etc/vfstab
Instead of:
/dev/vx/dsk/swapvol - - swap - no -
/dev/vx/dsk/rootvol /dev/vx/rdsk/rootvol / ufs 1 no logging
/dev/vx/dsk/var /dev/vx/rdsk/var /var ufs 1 no logging
Make it:
/dev/dsk/c0t0d0s1 - - swap – no –
/dev/dsk/c0t0d0s0 /dev/rdsk/c0t0d0s0 / ufs 1 no logging
/dev/dsk/c0t0d0s5 /dev/rdsk/c0t0d0s5 /var/ufs 1 no logging
# Double-check the /mnt/etc/system and comment out the rootdev entries
# if they are there
vi /mnt/etc/system
# Only comment out the following entries
rootdev:/pseudo/vxio@0:0
set vxio:vol_rootdev_is_volume=1
umount /mnt
reboot server in single user mode
apply patches
validate if everything goes smoothly, then:
vxdiskadm option 6
source disk rootdisk
target disk disk01
otherwise:
make changes in /etc/vfstab to reflect slices of vx-disk01
boot from vx-disk01(disk01)
encapsulate disk
mirror disk using vxdiskadm
29937 0 -rw-r--r-- 1 root root 4096 Mar 7 16:27 ./devices/virtual/block/VxVM3000/queue/scheduler
30024 0 -rw-r--r-- 1 root root 4096 Mar 7 16:27 ./devices/virtual/block/VxVM4000/queue/scheduler
30128 0 -rw-r--r-- 1 root root 4096 Mar 7 16:27 ./devices/virtual/block/VxVM4001/queue/scheduler
31259 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP2/queue/scheduler
31642 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP3/queue/scheduler
31780 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP4/queue/scheduler
31918 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP5/queue/scheduler
32056 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP6/queue/scheduler
32194 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP7/queue/scheduler
32301 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP8/queue/scheduler
32439 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP9/queue/scheduler
32546 0 -rw-r--r-- 1 root root 4096 Mar 5 11:51 ./devices/virtual/block/VxDMP10/queue/scheduler
21089 0 -rw-r--r-- 1 root root 4096 Mar 7 16:27 ./devices/pci0000:00/0000:00:09.0/0000:09:00.0/host0/rport-0:0-2/target0:0:0/0:0:0:0/block/sda/queue/scheduler
20640 0 -rw-r--r-- 1 root root 4096 Mar 7 16:27 ./devices/pci0000:00/0000:00:09.0/0000:09:00.0/host0/rport-0:0-2/target0:0:0/0:0:0:1/block/sdb/queue/
chrbl357:/sys # cat ./devices/virtual/block/VxVM3000/queue/scheduler
[noop] deadline cfq
chrbl357:/sys # cat ./devices/virtual/block/VxVM4000/queue/scheduler
[noop] deadline cfq
chrbl357:/sys # cat ./devices/virtual/block/VxDMP2/queue/scheduler
none
chrbl357:/sys # cat ./devices/virtual/block/VxDMP7/queue/scheduler
none
chrbl357:/sys # cat ./devices/pci0000:00/0000:00:09.0/0000:09:00.0/host0/rport-0:0-2/target0:0:0/0:0:0:0/block/sda/queue/scheduler
[noop] deadline cfq
chrbl357:/sys #
We change the scheduler option down the "/sys/block" path. In this instance we change it to noop but more often it is changed to deadline. However am confused about the scheduler file under VxVM3000 or VxDMPx. How does this interact with the block device scheduler settings?
Hi,
I want pratice VCS on vmware.
I have 4.1 sf_ha.cd1.4.1.00.0_phase2.x86.tar file to install VCS.also have License key to run VCS.
But i PC have 32 bit.
bash-3.00# isainfo -kv
32-bit i386 kernel modules
Pls guide me
Many Thanks
Tiger
HI ALL ,
I see a resource state in ONLINE|MONITOR TIMEDOUT state.What is this state ?How to clear this state ?
regards ,
siva
Any Video is available on Partnernet for Cluster File System ?
I found one free but its 6-7 hours long. Any way to download this. as I dont want to stick with Internet so long